Star-water-systems Lawn Pump User Manual download pdf

023474 G

LAWN PUMP QUICK

REFERENCE GUIDE

SEE INSTRUCTION MANUAL FOR

COMPLETE DETAILS

Questions, problems, missing parts?

Before returning to your retailer, call our

customer service department at

1-800-742-5044, 7:30 a.m. - 5 p.m., EST,

Monday - Friday.

NOTE: This pump is equipped with a 2 in. inlet for

maximum water spray.

• 2 in. inlet (suction) opening can be reduced with

some loss in performance. If reducing below

1-1/2 in., call factory.

• 1-1/2 in. outlet (discharge) pipe can be reduced with

some loss in performance. If reducing below 1-1/4 in.,

call factory.

NOTE: Pump may show water

stains as a result of factory

water testing.

TYPICAL INSTALLATION

CHECK YOUR BREAKER BOX

115V

230V

WARNING: Always disconnect

pump from electricity before performing

any work on the motor.

The motor of this pump is dual voltage and can run

on either 115V or 230V. This pump is pre-set in the

factory to run at 230V.

For 115V service, remove the motor cover and

change the following wires on the terminal board:

a. Using a pair of needle nose pliers, pull the gray

wire with the female flag connector from the “B”

terminal spade post. Place it to the left on the

“A” terminal space post.

HERE’S HOW TO CHANGE THIS

PUMP FROM 230V TO 115V

1. b. Pull the red wire with the female flag connector

from the “B” terminal. Place it to the right on the

L2 terminal space post.

A B

Water Level

25 ft.

max

Vertical

Lift

Outlet Pipe

Inlet

Pipe

Discharge to

Sprinkler System

Inlet pipe to water

Pipe

Support

60 ft. max.

Motor Cover

Foot

Valve

WHAT CONTROLS WILL YOU USE WITH

THIS PUMP?

Pump Start Relay Pressure Switch with

Tank

Indexing Valve

NOTE: This pump can be used with a variety of

controls. See control manufacturer’s instructions

for details.

This pump is wired for 230V

Need

115V?

see sectioN 4

230V

115V

For installation videos, scan with

your smart phone.

1. Disconnect the

outlet union and

separate the pipe.

2. Remove priming plug with

pressure gauge and the

air relief plug on top of

pump.

3. Slowly fill pump cavity until

water comes out of the air

relief hole.

4. Replace air relief plug and

continue adding water to

pump cavity until water

comes out the open

outlet pipe at the open

union.

6. Reconnect union on outlet

pipe. Open the ball valve

(turn handle to line up

with pipe), and then

turn on breaker to start

pump.

CAUTION: All pumps must be primed (filling

the cavity with water) before they are first operated.

This may take several gallons of water, as the inlet

line will be filled in addition to the pump cavity. The

longer the inlet line, the more water is required to

prime.

HOW TO PRIME YOUR PUMP

Outlet

Priming plug with

pressure gauge

Air relief

plug

Inlet

5. Wait 10 minutes to see if

water level drops below

the pipe tee. If level

drops, check foot valve.

If level stays constant,

re-install the priming plug.

Pipe

Tee

Star-water-systems Lawn Pump User Manual

Browse online or download User Manual for Pumps Star-water-systems Lawn Pump. Star Water Systems Lawn Pump User Manual

Summary of Contents

Comments to this Manuals

Star-water-systems Lawn Pump User Manual

Browse online or download User Manual for Pumps Star-water-systems Lawn Pump. Star Water Systems Lawn Pump User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Pumps Star-water-systems Lawn Pump

Relacionado con productos y manuales para Teléfonos Mitel M7310